15 Clever Dog Feeding Station Ideas You Can Build

Tired of tripping over your dog’s food and water bowls? Or perhaps you want a tidier, more elegant way to integrate your pet’s station into your decor? Check this out.

One of the best ways to tidy up your dog’s eating area is to create a dog feeding station either outdoors or indoors.

Fully furnished pet feeding areas will keep your dog’s food and water in a tidy place, reducing clutter in your space.

The best part about building your dog feeding station is that you can incorporate ideas that keep the bowls and mess away when your dog is done eating.

We have compiled 15 of the best ideas for dog feeding stations that can help you improve your pooch’s dining area. Check our top picks for some clever inspiration.

---

15 Dog Feeding Station Ideas

1. Dog Feeding Station DIY Outdoor

Tools Needed

• 25mm chisel
• Circular jigsaw
• Clamps (x2)
• Cordless drill
• 32mm spade bit
• Combination square
• Drop saw
• Earmuffs
• Fixing gun
• Hammer
• Jigsaw
• Measuring tape
• Nail gun and brads
• Orbital sander
• Pencil
• Plunge router
• Putty knife
• Safety glasses
• Work gloves

Materials & Supplies

• 360mm x 630mm x 17mm form ply (1 piece)
• 630mm x 110mm x 19mm Tasmanian oak (2 pieces)
• 360mm x 110mm x 19mm Tasmanian oak (2 pieces)
• 8g 35mm chipboard screws (4 pieces)
• Pot plant trays (2)
• Wood putty
• PVA or wood glue
• 120-grit sandpaper discs

Instructions

1. Cut your plywood to 320mm x 585mm. Mark a center line across the width of the board, measure 160mm down the length.
2. Align each bowl on the center line. Use a combination square to measure and mark the center of each bowl.
3. Drill pilot holes at your marks with a 5mm bit. Screw your board down outside the cutting area to keep it from moving.
4. Adjust the router arm so that the bit matches the radius of each bowl, minus the bowl’s lip, and then divide by two.
5. Cut circles for each bowl with the router. Put a scrap board under the plywood to protect your surface.
6. Adjust your drop saw to 45 degrees and cut one end of each Tasmanian oak board for the frame.
7. Mark and cut the opposite mitres, but leave a visible pencil line to help reduce cutting errors.
8. Mark and drill two 32mm holes around 100mm from each end of the side panels for the handles. Join the holes with a jigsaw.
9. Layout and glue the frame, nailing the sides and top in place with a nail gun. Make sure the edges are flush.
10. Fill any gaps or nail holes with wood putty, then lightly sand the whole piece with 120-grit sandpaper. Apply a sealant if your station will be holding water.
11. Place your bowls in the holes and slide the finished feeder under a bed or table when not in use.

---

2. Upcycled Stud Dog Feeding Station

Tools Needed

• Compound miter saw
• Mini Kreg jig
• Measuring tape
• Drill
• Jigsaw
• Sanding block or mouse sander
• Painter’s tape (ScotchBlue™ Advanced Multi-Surface)
• Paint brush or foam brush
• 1 reclaimed 6′ wall stud

Materials & Supplies

• Hairpin legs (9″ size)
• 2 stainless steel bowls
• 4″ drywall screws
• Small pot of bright paint (Lemon Zest by Behr used)
• Polycrylic protective finish

Instructions

1. Cut the reclaimed stud into 3, 22-inch sections. This will create the base of your feeding tray.
2. Attach the 3 pieces of wood, side by side, using the Kreg jig and drywall screws. Use screws at each end and in the center of each board to secure them tightly together.
3. Place the bowls upside down onto the tray and move them around to create an even sitting.
4. Measure with a tape measure to ensure they are an equal distance apart, then use a pencil to trace the perimeter of the bowl.
5. Use a jigsaw to cut out the circles, keeping just inside the pencil line so the bowl rims sit flush on the tray, without the possibility of dropping through.
6. Smooth all of the cut edges with a sanding block. Use a power sander to run over the entire surface to remove splinters and sand down the wood for an even surface.
7. Flip the tray over and use the Kreg jig to add extra screws along the joints to ensure the structure is strong and sturdy.
8. Attach the hairpin legs to the bottom with drywall screws, one leg in each corner to raise the tray off the ground.
9. Use painter’s tape along the top of the tray. Paint a border along the edge of the tray with a foam brush and your desired color. Allow to dry.
10. Apply 2 coats of Polyacrylic, letting dry between coats, over the entire tray to seal and protect the wood from any future spills.
11. Allow the piece to cure overnight. Place the bowls and station in your dog’s feeding area.

---

3. Rustic Pallet Wood Dog Feeder

Tools Needed

• Jigsaw
• Miter saw
• Handheld metal detector
• Carpenter square
• Electric nail gun
• Orbital sander
• Clamps
• Wood glue
• Spray lacquer
• Sharpie marker
• 120 grit sandpaper
• Safety glasses
• Respirator
• Gloves

Materials & Supplies

• Reclaimed pallet boards
• Dog bowls
• Scrap pallet board (optional for decoration)
• Tracing paper

Instructions

1. Separate warped and/or cracked boards, choosing the straightest, least damaged pieces in your pile. Look for boards that are in the ballpark for your desired width and thickness.
2. Roughly measure and sketch the size you want based on your dog’s height and your bowls’ dimensions.
3. Keep the box low enough for your dog to eat comfortably without straining. Adjust the overall footprint to accommodate your bowls and the boards you have.
4. Use a miter saw to cut the ends off of each of your boards. (You want to work from squared-off ends, potentially uneven edges.)
5. Cut all of the boards to a common length, checking each for nails first using a metal detector.
6. Arrange the boards into the desired box configuration and glue them together. Clamp the pieces to ensure a tight fit, then use a nail gun to finish securing the joints.
7. Add a support board down the center and two cleats along the underside of the box for stability.
8. Flip the bowls upside down on the top panel and trace around the outer edges. Use a smaller circular template to scribe the cut line inside the traced perimeter so the lip of the bowl will rest against the feeder.
9. Cut out the bowl cutouts with a jigsaw, leaving the inside of the smaller circle. Double-check that the bowls will sit properly in the cutout with their lips resting on the feeder.
10. Smooth all of the surfaces using an orbital sander and 120-grit sandpaper. Do not oversand, but do sand down edges and corners to smooth out any sharp splinters.
11. (Optional) Cut a fun shape out of some scrap wood and use a Sharpie to write your dog’s name. Allow the ink to dry, then spray the piece with a sealer.
12. Spray a few coats of spray lacquer all over the feeder. Allow each coat to dry, then lightly sand with the orbital sander to smooth out the finish. Allow the finish to fully dry.
13. Drop in the bowls and set your dog’s feeding station in place where he or she can easily access it.

---

4. Dog Feeding Station DIY with Storage

Tools Needed

• Screwdriver or drill
• Paintbrush or roller
• Measuring tape
• Clamps (optional)
• Saw (if modifying drawer faces or cutting a new top)

Materials & Supplies

• Old nightstand or stock cabinet
• Scrap wood for drawer faces or countertop
• Paint (Valspar Ultra White and French Linen were used)
• Cabinet pulls or handles
• Wheels (optional for mobility)
• Wood glue or construction adhesive
• Fabric bins or storage baskets
• Glass jars or turntables for treats

Instructions

1. Select a strong nightstand or small stock cabinet for your starting point. Remove broken drawer faces and replace them with scrap wood faces. Install new hardware, like cabinet pulls.
2. Paint the whole piece, using primer first. Paint in white, or another home-coordinating color. Contrast the top and body in different shades for interest, if desired.
3. Cut a scrap board for a top, if your stock cabinet doesn’t include one. Use wood glue, screws, and clamps to dry-fit and attach the top.
4. Install wheels on the bottom to make your station easy to wheel around for different locations in the kitchen or pantry, as needed.
5. Decide which drawers or cabinet space will hold what, to store food, treats, toys, leashes, meds, or other pet supplies. Keep the most-used items handy and easy to reach.
6. Arrange treats in glass jars or on clear turntables. Label jars, and set them in plain view for easy access.
7. Contain toys and puzzle games in fabric bins with windows or labels to view inside easily. Puzzles are easily seen through clear acrylic or windows.
8. Stack puzzles or bulky toys in an open basket on top, for added visibility and regular play.
9. Keep pet meds, or anything poisonous, out of reach, especially if small children or curious pets are in the home. Lock the cabinet, as needed.
10. Maintain your station in good order, and rotate your pet’s favorite toys or puzzle games over time, as their interests change.

---

5. Entryway With Dog Bowls

Tools Needed

• Pencil and ruler
• Paintbrush or small roller
• Clamps
• Circular saw
• Drill with 1/2″ hole saw bit
• Jigsaw
• Sander or fine-grit sandpaper

Materials & Supplies

• 2 plywood project panels (1″ thick, 2′ x 2′)
• 5–6 corner braces (1 1/2″ size)
• Construction adhesive
• Drywall anchors
• Drywall screws
• Spackle
• Wall touch-up paint
• Oil-based or exterior-grade paint
• Dog bowls

Instructions

1. Apply construction adhesive to bond the two plywood panels. This will create one thick board. Clamp tightly, then allow to dry overnight.
2. Plan and draw out the dimensions of the L-shape onto the plywood. In this project, both sides were 17″ long with a shallow 8″ depth.
3. Draw three evenly spaced bowl outlines onto the work surface. Use a bowl or a protractor to trace the circles. Measure and make sure they are spaced evenly and centered.
4. Cut out the L-shape using a circular saw. Use a 1/2″ hole saw to cut into the plywood at the center of each bowl outline. Then use a jigsaw to carefully cut around each circle.
5. Use a fine-grit sandpaper to sand all fresh cuts and edges. If needed, apply spackle to the plywood edges to create a smoother look, then sand and prime before painting.
6. Paint the feeding station with a high-quality, durable finish. Oil-based paint can sometimes take a long time to dry in a humid climate. In this case, a coating of exterior-grade paint can withstand moisture better.
7. Mount the corner braces into the wall using drywall anchors and screws. Place each bracket just under the bottom of the plywood base.
8. Place the feeding station onto the mounted corner braces. Drive one screw through each side of the base, into the wall, to prevent shifting.
9. Dry and cure before filling the dog bowls. You can store dog food below or above the station, or add toy baskets.

---

6. Elevated Dog Food Station with Storage Drawer

Materials & Supplies

• Marble contact paper
• Plastic screw-on feet
• Large drawer
• 10-gallon plastic food storage tote with lid
• Dog bowls

Instructions

1. Construct a feeding station with a broad top that has a drawer beneath. Ensure that the frame is sufficiently tall to accommodate a large breed dog, such as a 100-pound Rhodesian Ridgeback.
2. Cover the top of the feeding station with marble contact paper. This keeps the surface looking finished and keeps it safe from water and food contact.
3. Add plastic screw on feet to the bottom of the feeding station. The feet protect the bottom of the frame from moisture and also help the drawer to glide.
4. Insert the larger drawer into the bottom part of the feeding station. Add a 10-gallon plastic tote with a lid inside the drawer. The tote serves as a food container.
5. Cut 2 bowl-sized holes in the top panel and insert dog bowls. Cut the hole so that the bowl rims rest flat against the surface to keep the bowls in place during use.
6. Assemble the unit completely and add it to your dog’s feeding area. Ensure that the height is appropriate for your dog and provides easy access to the food and water bowls.

---

7. Upcycled Dresser Pet Feeding Station

Tools Needed

• Oscillating tool
• Dremel DSM20 Circular Saw with DSM500 Multipurpose Carbide Cutting Wheel
• Dremel Multi-Tool with Drill Bit (150)
• Dremel Multi-Tool with Spiral Multipurpose Cutting Bit (561) and Line & Circle Cutter (678)
• Drill
• Clamp
• Paintbrush

Materials & Supplies

• Old dresser
• Fresh piece of melamine
• Extra 19 mm plywood
• Wood screws (25.4 mm)
• Hinges
• Food and water bowls
• Wood moulding
• Construction adhesive

Instructions

1. Cut the dowel pins securing the dresser top in place with the oscillating tool. Remove the top and set aside. Remove and save the drawer fronts to be used in the false drawer configuration later.
2. Secure the top piece to the workbench and use the circular saw to cut the back edge of the top piece by 63.5 mm.
3. Cut the inner shelf out of melamine to fit the inner dimensions of the dresser. Cut 2 equal pieces to fit inside the lower drawer. This will be where the food and water bowls will sit.
4. Use the DSM20 saw to cut the 25.4 mm wide cleats marked on scrap plywood to size.
5. Trim the cleats and the inner divider to the dimensions of your dresser. Drill pilot holes in each cleat with the Dremel Multi-Tool and drill bit (150).
6. Secure cleats inside the dresser to support the inner shelf. Space them low enough to leave room for a large bag of dog food in the lower storage area. Fasten cleats to the interior of the dresser with wood screws.
7. Add cleats for hinge support, false drawer fronts, rear support, and additional shelf support, as needed, according to your design.
8. Fasten saved drawer fronts onto the front cleats to make a false front and maintain separation between the storage area and feeding area.
9. Replace the dresser top with the strip piece and secure with two hinges attached to the back cleat and the dresser top.
10. Use a template to mark two circles, the size of your bowls, on the lower drawer inserts. Measure the diameter of the bowl and subtract 12.7 mm to determine the cut size.
11. Cut out with the Dremel Multi-Tool, circle cutter, and cutting bit (561), rotating in a clockwise motion with firm pressure.
12. Add a finished edge by miter cutting wood moulding and fastening it to the bottom of the cabinet with the DSM20 and cutting guide. Clamp in place while cutting for a clean angle.

---

8. Crate-Based DIY Raised Dog Feeder

Tools Needed

• Compass
• Drill with a large drill bit
• Jigsaw
• Sandpaper
• Painting supplies (optional)

Materials & Supplies

• Wooden crate
• Stainless steel pet bowls with a lip
• Red chalk paint
• Hemp oil
• Dark wax
• Wax brush

Instructions

1. Begin with a wooden crate that is wide and deep enough to accommodate two bowls. Turn the box upside down so that the bottom becomes the top of your bird feeder.
2. Measure the inside diameter of each bowl (without the lip) and use a compass to trace two circles on the crate’s bottom (now top), centered and evenly spaced.
3. Drill a lead hole inside each circle with a large drill bit. Insert a jigsaw blade into the lead hole and cut out each circle.
4. Sand the edges of the circles to remove splinters and roughness. If you will paint or finish the crate, lightly sand the entire surface.
5. For a weathered paint finish, rub hemp oil on the edges of the crate. Brush red chalk paint over the entire surface and allow it to dry completely.
6. Sand the edges with coarse sandpaper to show some of the base color underneath. This will give the crate a distressed look.
7. Seal the entire piece with dark wax using a wax brush. Two coats will provide more protection against spills and wear.
8. After everything is dry, insert the bowls into the holes. Apply strips of felt to the underside of the crate if you want to protect your floors.

---

9. Dog Feeding Station for Two Dogs

Tools Needed

• Wood glue
• Saw
• Jigsaw
• Drill
• Hacksaw blade with handle

Materials & Supplies

• Old dresser
• Fresh piece of wood (for bowl shelf)
• Vinyl tablecloth (optional, for bowl shelf covering)
• Chalk paint (Waverly brand used)
• Furniture wax
• Dog bowls
• Plastic tote (for food storage)
• Sharpie marker

Instructions

1. Remove dirt from the dresser surfaces, then use wood glue to repair parts that have become loose or broken.
2. Plan which drawers to keep and which ones to remove based on where you will put the feeding bowls.
3. Remove drawer supports and any other wood you don’t need with a saw. Save any pieces you think you might want to use later.
4. Cut a new piece of wood to fit the opening where the drawers were removed.
5. Trace two holes on the front edge of the shelf using a plate with the same diameter as your bowl’s inside measurement.
6. Place the holes close enough to the front edge that the drawer below can still open all the way.
7. Use a drill to create starter holes at the edge of each circle. Use a jigsaw to cut the bowl openings. Test fit the bowls to make sure they sit evenly and securely.
8. Cover the new shelf with a vinyl tablecloth to allow for easy cleanup, or paint it instead. Paint the entire dresser with two coats of chalk paint and then seal with two coats of furniture wax.
9. Fit a plastic tote in the lower drawer for storing food. If the tote is too wide, use a Sharpie to mark where you will need to trim it and cut it to size with a hacksaw blade.
10. Put the food tote in the drawer and push the drawer back into the dresser. Place the shelf with bowl cutouts on top, leaving room for extras like treats or cat food.

---

10. Custom DIY Dog Feeding Station with Painted Detail

Tools Needed

• Jigsaw
• Chop saw
• Drill
• Compass
• Sandpaper
• Rag

Materials & Supplies

• 2 x 10 pine board
• Mid-century style furniture legs
• Screws
• Dog bowls
• White paint pen (Painters® brand)
• Rust-Oleum Wheat stain
• Accent paint (leftover pantry door paint)
• Annie Sloan clear wax
• IKEA plastic placemat (optional, for under feeder)

Instructions

1. Cut a 2 x 10 pine board to your desired length. This will be the feeding surface. You can also have the board cut at the store to save you time.
2. Cut four furniture legs to the desired height using a chop saw. Screw them to the board to form a strong raised platform.
3. Trace dog bowls onto the board using a compass or by placing the bowls on the board and tracing around them.
4. Cut approximately 1/4 in inside the line so the bowls will sit comfortably without falling through the openings.
5. Drill a starter hole at the edge of each circle, then use a jigsaw to cut the bowl openings. Lightly sand all edges cut with the jigsaw.
6. Use a white paint pen to draw your design (the author did simple ‘V’ shapes) on the top surface. Shake the pen well and test out on a piece of paper first.
7. Paint a coat of Rust-Oleum Wheat stain over the surface. Rub stain into the surface with a rag, then wipe away excess, which will leave the paint pen pattern showing through.
8. Once dry, paint the sides of the feeder and apply a dipped-paint look to the legs with the accent paint. Let dry.
9. Apply Annie Sloan clear wax all over the piece to seal and protect against water and food messes.
10. Slide the bowls into the openings, and place a plastic mat underneath if you like to protect your floors.

---

11. Dog Food and Water Station

Tools Needed

• Drill
• Spade bit set
• Jigsaw
• Mouse sander

Materials & Supplies

• 1″ x 8″ x 2′ wood board
• 4 end table legs
• Leg plates with screw sets
• 3 gold dog food bowls (2 small, 1 medium)
• Simple trim for edges
• Liquid Nails
• Paint

Instructions

1. Sketch out on the wooden board where you want to place all three bowls, then add a center line for guidance to keep your spacing and layout symmetrical.
2. Drill a starter hole inside each traced circle with a spade bit to provide an entry point to the jigsaw blade.
3. Cut out each bowl hole with a jigsaw. Stay a little inside the traced line so the rim of the bowl is snug in the hole. Use a mouse sander to sand the edges of the holes smooth.
4. Attach the leg plates to the bottom of the board with the screws included in the kit. Screw each leg in by hand. If a leg overlaps a bowl cutout, omit one screw. It will still be stable.
5. Glue trim pieces around the perimeter of the board with Liquid Nails. This helps to conceal any visible hardware and looks more finished.
6. Paint the piece your chosen color. Once the paint is dry, set the bowls in the cutouts, and your feeder is ready to go.

---

12. Dog Bowl Chair Feeding Station

Tools Needed

• Sander
• Drill
• Jigsaw
• Silhouette machine (optional)

Materials & Supplies

• Old wooden chair
• Mixing bowl (used as a dog bowl)
• Stain
• Clear protective finish (Minwax Helmsman Spar Urethane Satin Finish)

Instructions

1. Begin by sanding the chair. You want to make sure that any surface finish is removed and that you get rid of the buildup of oils so that your new stain can absorb.
2. Put your mixing bowl upside down in the center of the chair seat and trace around it to make the outer circle.
3. Then draw a slightly smaller circle inside that one. This will be your cutting line, so the bowl will sit in the seat and not drop through.
4. Drill a starter hole in the inner circle and make sure it is large enough to fit the jigsaw blade in it.
5. Put the jigsaw blade in the starter hole and cut along the line you drew in the middle. Try to go slowly and carefully so that you do not cut off any rough edges.
6. Place the bowl in the cutout and see if it fits. If not, you can trim a little more using your jigsaw. It is better to cut too little and need to remove more than it is to cut too much.
7. Once the bowl fits cut the splinters off with sandpaper so that the surface of the seat is smooth.
8. You can now add vinyl lettering or word art if desired. A Silhouette makes this easy. This is when you will want to customize it for your child.
9. Add a coat of stain and let it dry according to the directions on the can.
10. Finish by adding a coat of a clear protective topcoat such as Minwax Helmsman Spar Urethane so that it will withstand slobber, water spills, and the daily wear of a kids’ chair.

---

13. Dog Feeding Station in Laundry Room

Tools Needed

• Cordless drill
• Jigsaw or circular saw
• Stud finder
• Measuring tape
• Level
• Utility knife
• Drywall saw
• Sandpaper
• Nail gun (optional)

Materials & Supplies

• ¾” or ½” plywood or MDF
• 2 cabinet hinges
• 2 lengths of decorative chain
• Latch or magnetic closure
• Screws
• Wood glue
• Dog bowls
• Picture frame or art
• Paint or stain
• Pet-safe sealant
• Optional: baskets or a small bin for kibble

Instructions

1. Find a large enough, clear section of wall between two studs. Run a stud finder over the wall and mark the open cavity on the wall.
2. Use a utility knife to trace the outline and cut the opening with a drywall saw. Keep the drywall piece aside, as it may be useful later on for the backing or to help with measurements.
3. Measure and cut your plywood to create the interior box. You will need two side pieces that are the height of your opening.
4. Use wood glue and screws to build the box together and sand down all edges for a smooth finish. Paint or stain the entire box, then coat with a pet-safe finish.
5. Install the front flap using cabinet hinges attached to the bottom edge of the flap. Use a decorative chain on each side to hold the flap in place so it opens horizontally and stays level.
6. You can use a latch or magnetic catch to keep it flush against the rest of the box when not in use.
7. Add a wooden lip inside the flap to keep the bowls from sliding around, and you may want to cut a removable insert to make cleanup even easier.
8. With the feeding station in place, use a lightweight picture frame or piece of wall art to cover it up using a French cleat.
9. Place your dog bowls inside and fill them with your dog’s favorite food. You can also place a small bin or basket of kibble in the nook as well if there’s room.

---

14. Built-In Dog Feeding Station in Island

Tools Needed

• Measuring tape
• Saw
• Drill
• Sandpaper or sander
• Pry bar
• Hammer
• Utility knife
• Drywall saw
• Pocket hole jig
• Tile tools (trowel, grout float)
• Plumbing tools (wrench, pipe cutter)

Materials & Supplies

• ¾” plywood
• 2 x 4 lumber
• Pot filler faucet
• Plumbing fittings and connectors
• Stainless steel dog bowls
• Drywall
• Drywall screws
• Tile and tile adhesive
• Grout
• Paint or stain
• Waterproof sealant
• Screws and wood glue

Instructions

1. Mark the height and depth of the space that you have to work with on your island for the feeding station, then determine the height of the bowls based on your dog’s height.
2. Pry the existing paneling off the side of the island with a pry bar and hammer. Cut out the drywall that backs the panel to expose the framing that will fit the feeding station.
3. Cut the ¾” plywood to the desired dimensions for the box frame that will house the bowls. Sand down the edges and cut out openings for the bowls.
4. Install an internal framing wall with 2 x 4 that will support both the feeding station and the pot filler plumbing. Screw the frame firmly under the island, checking that it is square and level.
5. Attach the pot filler faucet to the 2 x 4 frame, then connect the water line. Test for leaks, then move on when you’re finished. If you’re not comfortable with plumbing, consider hiring a pro.
6. Secure the drywall over the exposed 2 x 4s to close off the section and provide a surface for either tile or finishing. Cut the drywall to size, screw it in place, then prepare the surface.
7. Install the plywood face frame over the front of the feeding station with glue and screws. This will frame the bowls, providing a finished look that matches the cabinetry.
8. Stain the face frame to match the island. Allow the stain to dry, then seal it with a waterproof, pet-safe finish to protect it from spills and damage.
9. Tile over the drywall section with tile adhesive. Grout the tile, wiping off the excess. This adds durability and integrates the station into your kitchen’s design.
10. Cut a countertop from ¾” plywood to cover the feeding station. Sand and stain the surface to match, then seal it. Allow the sealer to dry, then screw the countertop to the top of the unit.
11. Install the stainless-steel bowls, test the pot filler for functionality, then enjoy your built-in feeding station.

---

15. Dog Feeding Station Kitchen

Tools Needed

• Pencil or marker
• Saw or cutting tool 
• Measuring tape

Materials & Supplies

• 1 x 600 mm 1-drawer base cabinet
• 1 x microwave box
• Pet food bowl
• Pet water fountain
• PVA glue or silicone sealant

Instructions

1. Trace the outline of your pet food bowl and water fountain on the base of the microwave box. Mark the location of the cutouts with a pencil or marker.
2. Cut both shapes out, making the holes a little smaller than the outlines. The goal is to have the bowl and fountain sit on the lip of the cutout opening, instead of dropping through it.
3. Pay attention to the orientation of the cabinet legs when cutting out the holes. Don’t cut to the sides. Leave a minimum of 35mm free around the edges to avoid screwing into anything.
4. Apply a layer of PVA glue or silicone to the raw edges of the cutouts to prevent moisture damage. Insert the bowl and fountain into place when the sealant has dried.
5. Ensure your fountain is near a power outlet for easy access to electricity.

---

Conclusion

Be it repurposing an old chair, modifying your kitchen island, or making use of a secret wall nook, these projects above prove that dog feeding station ideas can be classy and useful.

Raised feeders are easier on dogs’ backs and necks, while built-in and hidden versions keep clutter off your counters and make your home look more thoughtfully designed.

With something for every space, housemate, and taste, there’s an option above that’s almost certain to provide the perfect solution for you and your dog.

The best part? Most of the projects listed above don’t require professional help. You can just do it by yourself, maybe with an extra person to help out.

As a bonus, most of these are weekend DIY projects. So, make sure to choose a design that will work for you and your space to give your dog the gift of a dog feeding station.

---

Further Reading:

22 Creative DIY Dog Food Storage Ideas

11 Elevated Dog Bowls DIY Ideas